Customer Service: Mon – Fri 8.00-17.30. This Turbocharger fits the following vehicles. BMW 120d, 220d, 320d, 520d, 520 GT, X1, X3 2.0d 163/184HP – 120/135Kw 2010. If you think this Turbocharger fits your vehicle and cannot find your matching part number or Vehicle please feel free to message us for further assistance! These are the two options. We will respond with our postal address. If you have any questions please feel free to message us! UK non remote areas ONLY. This relates to all UK, non remote areas as per the DPD website. Channel Islands, Isle of Wight, Isle of Man, Scilly Isles, Scottish Highlands, Scottish Islands, Northern Ireland. WE WILL NOT ACCEPT. Parts that have been used/fitted or tampered with. Please note if you are a third party fitter or if you are fitting yourself, it is your responsibility to read & follow these instructions thoroughly or pass to the third party fitter for their pursual prior to point of fitment. Use liquid gasket when fitting a turbo, this may enter the turbo & cause severe damage. Why did your original Turbo fail? IMPORTANT – DO NOT FIT YOUR TURBO UNLESS YOU HAVE THE ANSWER. The THREE MOST COMMON CAUSES ARE. This can be the result of Blockages i. Carbon particles, silicon contamination, bent or kinked pipes, leaking pipes, low oil level, worn/faulty oil pump or lack of oil priming when the turbo was fitted. Blockages & leaks in the air & exhaust system can alter the pressure at the turbo & cause oil leakage. This can be caused by fuel, water, foreign objects or carbon deposits, overdue oil or filter change, incorrect or poor quality oil or filter, malfunctioning filter bypass valve. Damage, can be due to leaks in the air intake system, particles remaining from the failed turbo, washers, gasket material, rag particles, etc in the air intake. Even a very small object can cause severe damage. (PLEASE ALSO REFER TO’WARNING’/ CRITICAL FITTING SHEET SUPPLIED WITH YOUR TURBO) SOME turbos come with critical fitting instructions. Such as oil pipe replacement, breather replacement, EGR replacement, which must be followed for a successful installation. Please refer to the envelope enclosed with your turbo for these critical instructions. The turbo is an integral part of the air fuel, cooling & oil systems, so ensure they are all working correctly, with the right fluid levels & no leaks or blockages. Replace any failed or suspect parts with new. Check the air intake pipes & exhaust manifold to ensure they are free from contamination, to avoid debris entering the turbo. Check the oil inlet & drain pipes are clean & free from obstructions, internal carbon & sludge. Clean or replace if necessary. Replace the engine oil & filter, remembering to prime the filter. Check the exhaust is free from cracks & carbon debris, & the studs are in good condition. Check the manifold casting is not cracked on the outside or breaking up internally. If in doubt, replace with a new part. Mount the turbo on the exhaust flange, checking the turbine gasket fits correctly to give a gas-tight seal. Connect the oil drain pipe. Prime the turbo by filling the oil feed hole with clean engine oil, rotate the rotor assembly by hand, to ensure the oil protects the bearings. Connect the oil feed pipe to the turbo. Lack of oil priming during fitting, & incorrect starting procedure, can cause premature turbo failure. Connect all other external fittings to the turbo. Make sure the engine oil circulates & the turbo is thoroughly lubricated before it operates under load. Disconnect the ignition system or fuel supply, so the engine turns over without firing up. Check the oil pressure warning light goes out. Reconnect the ignition or fuel supply & start the engine. Run it at a fast idle while you check there are no diagnostic fault codes, or oil, air, exhaust gas or fuel leaks. After driving your vehicle allow the engine to idle for 30 to 60 seconds to allow the oil to recirculate back through the turbo & the turbine shaft to stop spinning, thus preventing carbon build up. Please keep a record of oil & filter changes Thank you. Tab 4 Content Tab 4 Content Tab 4 Content. This item is in the category “Vehicle Parts & Accessories\Car Parts & Accessories\Air & Fuel Delivery\Turbos, Superchargers & Intercoolers\Turbos & Parts”. The seller is “turbosandparts” and is located in this country: GB. This item can be shipped to United Kingdom.

• Type: Turbocharger
• Manufacturer Part Number: 49335-00510 49335-00584
• Reference OE/OEM Number: 49335-00510 49335-00511 11658519477, 49335-00512 49335-00520 11658506721, 49335-00521 49335-00530 8515187 8515188, 49335-00531 49335-00550 49335-00560 8512464, 49335-00561 49335-00570 49335-00580 851745203C, 49335-00581 49335-00583 49335-00584 851329801A, 49335-00500 11658512465
• Brand: Mitsubishi (Genuine OE)

Customer Service: Mon – Fri 8.00-17.30. This Turbocharger fits the following vehicles. BMW 120d, 220d, 320d, 520d, 520 GT, X1, X3 2.0d 163/184HP – 120/135Kw 2010. If you think this Turbocharger fits your vehicle and cannot find your matching part number or Vehicle please feel free to message us for further assistance! These are the two options. We will respond with our postal address. If you have any questions please feel free to message us! UK non remote areas ONLY. This relates to all UK, non remote areas as per the DPD website. Channel Islands, Isle of Wight, Isle of Man, Scilly Isles, Scottish Highlands, Scottish Islands, Northern Ireland. WE WILL NOT ACCEPT. Parts that have been used/fitted or tampered with. Please note if you are a third party fitter or if you are fitting yourself, it is your responsibility to read & follow these instructions thoroughly or pass to the third party fitter for their pursual prior to point of fitment. Use liquid gasket when fitting a turbo, this may enter the turbo & cause severe damage. Why did your original Turbo fail? IMPORTANT – DO NOT FIT YOUR TURBO UNLESS YOU HAVE THE ANSWER. The THREE MOST COMMON CAUSES ARE. This can be the result of Blockages i. Carbon particles, silicon contamination, bent or kinked pipes, leaking pipes, low oil level, worn/faulty oil pump or lack of oil priming when the turbo was fitted. Blockages & leaks in the air & exhaust system can alter the pressure at the turbo & cause oil leakage. This can be caused by fuel, water, foreign objects or carbon deposits, overdue oil or filter change, incorrect or poor quality oil or filter, malfunctioning filter bypass valve. Damage, can be due to leaks in the air intake system, particles remaining from the failed turbo, washers, gasket material, rag particles, etc in the air intake. Even a very small object can cause severe damage. (PLEASE ALSO REFER TO’WARNING’/ CRITICAL FITTING SHEET SUPPLIED WITH YOUR TURBO) SOME turbos come with critical fitting instructions. Such as oil pipe replacement, breather replacement, EGR replacement, which must be followed for a successful installation. Please refer to the envelope enclosed with your turbo for these critical instructions. The turbo is an integral part of the air fuel, cooling & oil systems, so ensure they are all working correctly, with the right fluid levels & no leaks or blockages. Replace any failed or suspect parts with new. Check the air intake pipes & exhaust manifold to ensure they are free from contamination, to avoid debris entering the turbo. Check the oil inlet & drain pipes are clean & free from obstructions, internal carbon & sludge. Clean or replace if necessary. Replace the engine oil & filter, remembering to prime the filter. Check the exhaust is free from cracks & carbon debris, & the studs are in good condition. Check the manifold casting is not cracked on the outside or breaking up internally. If in doubt, replace with a new part. Mount the turbo on the exhaust flange, checking the turbine gasket fits correctly to give a gas-tight seal. Connect the oil drain pipe. Prime the turbo by filling the oil feed hole with clean engine oil, rotate the rotor assembly by hand, to ensure the oil protects the bearings. Connect the oil feed pipe to the turbo. Lack of oil priming during fitting, & incorrect starting procedure, can cause premature turbo failure. Connect all other external fittings to the turbo. Make sure the engine oil circulates & the turbo is thoroughly lubricated before it operates under load. Disconnect the ignition system or fuel supply, so the engine turns over without firing up. Check the oil pressure warning light goes out. Reconnect the ignition or fuel supply & start the engine. Run it at a fast idle while you check there are no diagnostic fault codes, or oil, air, exhaust gas or fuel leaks. After driving your vehicle allow the engine to idle for 30 to 60 seconds to allow the oil to recirculate back through the turbo & the turbine shaft to stop spinning, thus preventing carbon build up. Please keep a record of oil & filter changes Thank you. Tab 4 Content Tab 4 Content Tab 4 Content. This item is in the category “Vehicle Parts & Accessories\Car Parts & Accessories\Air & Fuel Delivery\Turbos, Superchargers & Intercoolers\Turbos & Parts”. The seller is “turbosandparts” and is located in this country: GB. This item can be shipped to United Kingdom.

• Type: Turbocharger
• Manufacturer Part Number: 49335-00510 49335-00584
• Reference OE/OEM Number: 49335-00510 49335-00511 11658519477, 49335-00512 49335-00520 11658506721, 49335-00521 49335-00530 8515187 8515188, 49335-00531 49335-00550 49335-00560 8512464, 49335-00561 49335-00570 49335-00580 851745203C, 49335-00581 49335-00583 49335-00584 851329801A, 49335-00500 11658512465
• Brand: Mitsubishi (Genuine OE)

REMANUFACTURED TURBOCHARGER + Gaskets. BMW 120d 320d 520d X3 2.0d. TESTED WITH TURBOCLINIC AIR FLOW RIG. This means that youll. Have to send us your old unit. After we receive your old turbocharger we will transfer. You must send your old unit back to us within. Costs from your own expenses. Please check your Part number and OEM number which. Are located on your turbocharger aluminum housing. To make sure that they match the ones which you. Can find in our part description. If you cant find. Your part number or you just want us to. Confirm the part, please feel free to. Turboclinic VNT Analyser / turbo calibration bench is the most advanced equipment on the market toadjust turbocharger’s variable nozzles with pneumatic or electronic actuators. It enables to set the correct position of the variable nozzles and adjusts the minimum and maximum flow of the turbocharger. Our turbocharger core CHRA balanced with high speed VSR trim by CIMAT. CIMAT is a part of American group BEP, which supplies end of the line and balancing solutions to car manufacturers like GM, Mercedes, Audi, VW etc. Tester ATD-1 can test and reset VGT electronic. Actuator used on BorgWarner KKK turbochargers. For Volkswagen and Audi engines as well as. Mitsubishi turbochargers for BMW. Programmer APD-1 is professional device designed for. Reprogramming Hella electronic actuators used in. By purchasing and fitting this turbocharger you agree to all the above terms andconditions of sale. From date of invoice or 24,000 miles whichever falls first. From date of invoice. Please call 01708725406 or 07919151752 before returning turbocharger / cartridge. It may be possible that we can consult you and help to fix the problem without returning the turbocharger / cartridge to us. · ancillary charges such as removal and refitting / hire of vehicles etc. · any damage caused to engine or vehicle by failed turbocharger. Filter, new oil, banjo bolts, oil feed pipe, drain pipe – other parts may also need to be changed, please. Refer to the fitting instructions and invoice from a professional garage / mechanic for fitting parts mentioned above. Your turbocharger will have any visible impact damage. For example if your. Turbocharger cartridge compressor wheel is damaged by fell in nut. Actuator housing has to be. · Your turbocharger cartridge housing and inside parts will be blue colour. This is a symptom of. Overheating which happens because of oil starvation. · If your turbocharger seals are broken, unless you have prior permission from us to do so in writing. · If your vehicle ECU was remapped. The item “BMW 120d 320d 520d X3 2.0d 163-184KW 49335-00510 49335-00584 Turbo + Gasket Kit” is in sale since Thursday, December 8, 2016. This item is in the category “Vehicle Parts & Accessories\Car Parts\Turbos & Superchargers\Turbochargers & Parts”. The seller is “london_turbos” and is located in Romford. This item can be shipped to United Kingdom.

• Modified Item: No
• Custom Bundle: No
• Type: Turbocharger
• Non-Domestic Product: No
• Manufacturer Part Number: 49335-00510 49335-00584
• Reference OE/OEM Number: 49335-00510 49335-00511 11658519477
• Brand: Mitsubishi (Genuine OE)